Categories

Login

    Username / Email:
    Password:

Brands

BODY & COLLISION REPAIR

BODY & COLLISION REPAIR
  • STECK Right Angle SeamBuster

    STECK Right Angle SeamBuster

    This heavy-duty chisel allows you to easily separate spot welded or bonded panels. Save up to 15 minutes per panel replacement. Sharpened on two edges. the sharp end allows for penetration between panels and the side edge allows for side impact to drive More Info
    0 Review(s)
  • Mo-Clamp GM “R” Hook

    Mo-Clamp GM “R” Hook

    Specifications: Overall length: 11” (280 mm), Weight: 2 lbs. (.91 kg), Capacity: 5 tons (4,536 kg). 3/8” (9.53mm) Chain (Gold) More Info
    0 Review(s)
  • Mo-Clamp Maxi Tac-N-Pull

    Mo-Clamp Maxi Tac-N-Pull

    Design allows for angled and/or uneven pulls and getting around obstructions. Made of Mo-Clamp Tru-Tuff steel alloy. Covered by the Mo-Clamp forever warranty. Can use all 5 different sizes of pull plates, in whatever combination is required. Comes with (2 More Info
    0 Review(s)
  • Mo-Clamp Slim Line Sill Hook

    Mo-Clamp Slim Line Sill Hook

    Use this new hook from Mo-Clamp to pull front hinge pillars, center pillars posts, rear hinge sections or any location where you need a broad, thin pulling surface. Made from Mo-Clamp Tru-Tuff© drop-forged, heat-treated alloy steel with a pulling capacity More Info
    0 Review(s)
  • Mo-Clamp Large Panel Puller

    Mo-Clamp Large Panel Puller

    Design allows technician to pull wider areas from behind door posts, pillars and rocker panels. Also gives technician the ability to get behind core supports and other tough areas with a wider pulling surface. Specifications: Overall length 9" (228mm) Pul More Info
    0 Review(s)
  • Mo-Clamp Tie Down Hook Cluster

    Mo-Clamp Tie Down Hook Cluster

    Ever get really frustrated when you need a special sized hook and can't find it? Well, here's the newest in that family of holding devices. The Hook Cluster™ with chain will most likely do the job when the others quit. The very most common tie downs all a More Info
    0 Review(s)
  • Mo-Clamp 3/8” (9.53mm) Mo-Clamp Frame Straightening Chain

    Mo-Clamp 3/8” (9.53mm) Mo-Clamp Frame Straightening Chain

    Working load limit: 6,600 lbs. Proof test 20,000 lbs. (9,070 kg). the weight of the chain is 2 lbs. per foot (.91 kg). The weight of the Grab Hook is 1 lb. (.45 kg) include one #6210 Grab Hook More Info
    0 Review(s)
  • Mo-Clamp Jr Clamp

    Mo-Clamp Jr Clamp

    One of Mo-Clamp's original self-tightening clamps. A must for every body man. 1½" wide bite for aggressive pulling. Original wedge. New angled tooth design. Gripping Surface: 1½" wide (38 mm), ¾" deep (19 mm) Overall Length: 9" (229 mm) Weight: 5 lbs (2.2 More Info
    0 Review(s)
  • Mo-Clamp T.O. Clamp (Tight Opening)

    Mo-Clamp T.O. Clamp (Tight Opening)

    Mo-Clamp's re-introduced the Tight Opening Clamp because popular demands had to be met so the old design is back. Still a full 3 ton capacity. Still able to reach core support and upper sheet metal areas where no other can. Perfect for small pick-up frame More Info
    0 Review(s)
  • Mo-Clamp Four-Way Pull Clamp

    Mo-Clamp Four-Way Pull Clamp

    Clamp has recessed pockets to hold bolts stationary for easy tightening. Includes #4043 Oval Loop. Gripping Surface: 4" wide (102 mm), 3/4 " deep (19 mm) Overall Length: 8" (203 mm) Weight: 12 lbs (5.45 kg) Capacity: 6 tons (5,443 kg) Replacement Parts: # More Info
    0 Review(s)
  • Mo-Clamp Ford “T” Hook

    Mo-Clamp Ford “T” Hook

    Specifications: Overall length: 10 1/2” (267 mm), Weight: 2 lbs. (.91 kg), Capacity: 4 tons (3,629 kg). More Info
    0 Review(s)
  • Mo-Clamp Mini Deep Hook Set

    Mo-Clamp Mini Deep Hook Set

    For fast hook-ups on cowls, door posts and trunk openings, or to reach into cramped places. Includes #210060 Horizontal Bracket and #210070 Vertical Bracket. Brackets are interchangeable with the #6400 Regular Deep Hook Set and #6410 Jumbo Deep Hook Set. More Info
    0 Review(s)
  • Mo-Clamp 5” Down Pulley/Snap Block Assembly

    Mo-Clamp 5” Down Pulley/Snap Block Assembly

    A combination of the #5810 Down Pulley Assembly and the #5811 Block Pulley Adapter it is perfect for horizontal pulls. Capacity: 5 tons (4,536kg) Heat Treated Steel. Made in the U.S.A. More Info
    0 Review(s)
  • Mo-Clamp Three-Way Pull Clamp

    Mo-Clamp Three-Way Pull Clamp

    Clamp has recessed pockets to hold bolts stationary for easy tightening. Includes #4043 Oval Loop. Gripping Surface: 4" wide (102 mm), 1/2 " deep (19 mm) Overall Length: 8" (203 mm) Weight: 8 lbs (3.63 kg) Capacity: 6 tons (5,443 kg) Replacement Parts: #4 More Info
    0 Review(s)
  • Mo-Clamp Tac-N-Pull Pull Plate Kit

    Mo-Clamp Tac-N-Pull Pull Plate Kit

    For hard-to-hold pulls. Tack weld one of the reusable plates. Attach clamp and pull. Break tack weld with a grinding cut-off wheel or cutting torch. The Pull Plate Kit includes: Ten (10) #0801 1" Pull Plates Five (5) #0802 11/2" Pull Plates Five (5) of #0 More Info
    0 Review(s)